自上料搅拌机

24小时服务热线

400-879-1999

点击拨打服务热线:400-879-1999

新闻资讯

首页>>资讯中心>>新闻资讯>>冲压式潜水搅拌机的长期维护少不了!

冲压式潜水搅拌机的长期维护少不了!

来源:https://www.zishangliaojiaobanji.cn 日期:2021-04-30 发布人:admin
概述:冲压式潜水搅拌机又被称为潜水推进器,它可以用在污水处理厂的工艺流程中推进搅拌含有悬浮物的污水、稀泥浆、工业过程液等,创建水流,加强
冲压式潜水搅拌机又被称为潜水推进器,它可以用在污水处理厂的工艺流程中推进搅拌含有悬浮物的污水、稀泥浆、工业过程液等,创建水流,加强搅拌功能,防止污泥沉淀,因此它可以用在很多工业化工生产的过程之中。
Stamping submersible mixer is also known as Submersible Propeller. It can be used in the technological process of sewage treatment plant to promote the mixing of sewage, thin mud, industrial process liquid containing suspended solids, create water flow, strengthen the mixing function and prevent sludge precipitation. Therefore, it can be used in many industrial and chemical production processes.
潜水搅拌机采用双曲线水力模型,效率高,叶片不同角度可以提供不同的搅拌混合能力;研发新型潜水电机(绝缘等级F级或H级),外形美观,效率高,节能效果明显;采用冷轧矽钢片,抗过载能力强,不易烧损;两道独立的机械密封,保证潜水电机长期可靠运行。
The submersible mixer adopts hyperbolic hydraulic model, which has high efficiency. Different angles of blades can provide different mixing capacity; Research and development of new submersible motor (insulation class F or H), beautiful appearance, high efficiency, energy saving effect is obvious; Cold rolled silicon steel sheet is adopted, which has strong overload resistance and is not easy to burn; Two independent mechanical seals ensure the long-term and reliable operation of submersible motor.
小型搅拌机
冲压式潜水搅拌机如果进行长期的使用,必须要注意它的保养和防护,这样才能够使它发挥更加长期的作用。潜水搅拌机在投入运行后,定期进行维护和保养才能更好的发挥它的作用。
If the stamping submersible mixer is used for a long time, we must pay attention to its maintenance and protection, so as to make it play a more long-term role. After the submersible mixer is put into operation, regular maintenance can better play its role.
1、换油:冲压式潜水搅拌机一般每半年需要更换一次润滑油,润滑油的型号为32#机械油,换油时,小心拧开油塞,放进其内存油,注意油枪内可能会有剩余的内压,以防油的喷射。
1. Oil change: the stamping submersible mixer generally needs to change the lubricating oil once every six months. The type of lubricating oil is 32 # machine oil. When changing the oil, carefully open the oil plug and put the oil into its memory. Pay attention that there may be residual internal pressure in the oil gun to prevent the oil from spraying.
2、潜水搅拌机机械密封的组装和拆卸:组装必须在非常干净的环境条件进行,装配介质为纯净的润滑油。首先必须洗净机械密封的各个部位,接着将两端机械密封的静环装置均匀平稳的压入定位孔中,注意保护好静环密封面,切不可损坏密封面,然后利用导向套将动环装入轴上,合上油室端盖,注意不要碰撞到机械密封的密封面,机械密封的拆卸,可按上面的反顺序进行。
2. Assembly and disassembly of mechanical seal of submersible mixer: the assembly must be carried out in a very clean environment, and the assembly medium is pure lubricating oil. First of all, all parts of the mechanical seal must be cleaned. Then, the static ring devices of the mechanical seal at both ends must be pressed into the positioning hole evenly and smoothly. Pay attention to protect the sealing surface of the static ring. Do not damage the sealing surface. Then, use the guide sleeve to install the dynamic ring into the shaft and close the end cover of the oil chamber. Pay attention not to collide with the sealing surface of the mechanical seal, This can be done in reverse order.
3、轴承润滑脂:一般大修时更换一次,润滑脂量为轴承腔间隙1/3到1/2处,润滑脂推荐采用高温钙纳基润滑脂。
3. Bearing grease: it should be replaced once in general overhaul. The amount of grease should be 1 / 3 to 1 / 2 of the bearing cavity clearance. High temperature calcium nano base grease is recommended.
4、潜水搅拌机的泄露保护处理:假如渗漏开关保护,表示电机侧的机械密封损坏,必须要检查和修理,打开油室腔的堵塞,排尽其内积液。
4. Leakage protection treatment of submersible mixer: if the leakage switch is protected, it means that the mechanical seal on the motor side is damaged. It must be checked and repaired. Open the blockage in the oil chamber and drain the liquid in it.
本文的精彩内容由小型搅拌机提供的精彩内容分享,更多的精彩内容请点击进入我们的网站:https://www.zishangliaojiaobanji.cn,我们会有更多的精彩内容等您查看,欢迎大家来电咨询.
The wonderful content of this article is shared by the wonderful content provided by the small mixer. For more wonderful content, please click to enter our website: https://www.zishangliaojiaobanji.cn , we will have more wonderful content waiting for you to check, welcome to inquire
此文关键词:小型搅拌机

推荐阅读/ Recommended reading

其实轻量化这个词很好理解,轻,轻量型的发动力,更环保,轻量型的车身,自重轻,不超重,更安全,是一款安全又环保的搅拌车。混凝土搅拌车

自动上料搅拌车购买了不会操作怎... 2021-06-16
高速搅拌机的电动机功率的要求特点 2021-06-15
搅拌车生产质量应该注意什么? 2021-06-10
自上料搅拌机转向泵出现问题怎么... 2021-06-09
自动上料搅拌车搅拌轴停止转动怎... 2021-06-08
自上料搅拌机搅拌斗由哪些内容组... 2021-06-07
自上料搅拌机搅拌斗由哪些内容组... 2021-06-07
自上料搅拌机防止沾罐快装快卸是... 2021-06-04

截屏,微信识别二维码

微信号:1234567

点击微信号复制,添加好友

 打开微信