您好,欢迎光临!中科聚峰机械有限公司网站!

莱州聚峰机械有限公司

定制咨询热线:400-879-1999

新闻资讯

首页>>资讯中心>>新闻资讯>>自上料搅拌机零件破损速度快的原因
联系我们
莱州聚峰机械有限公司

联系人:刘经理

电话:400-879-1999

地址:山东省莱州市206国道与308省道交叉口东南50米

自上料搅拌机零件破损速度快的原因

来源:https://www.zishangliaojiaobanji.cn 日期:2022-04-29 发布人:zhongke
概述:  在机器工作中经常会出现零件破损的问题,一定程度上会严重影响工作效率,那么你知道自上料搅拌机零件破损速度快的原因是什么吗?下面就
  在机器工作中经常会出现零件破损的问题,一定程度上会严重影响工作效率,那么你知道自上料搅拌机零件破损速度快的原因是什么吗?下面就来找找原因吧。
  In the work of the machine, parts are often damaged, which will seriously affect the work efficiency to a certain extent. Then do you know the reason why parts of the self-feeding self-feeding mixer are damaged at a fast speed? Let's find out why.
  自上料搅拌机通常是采用叶轮式搅拌,设备上设置有辅助的吸风口,可通过调节板适当的打开吸风口。自上料搅拌机在工作时,经过搅拌后的原料可及时排出筛网。
  Self-feeding mixer is usually impeller type mixing, the equipment is provided with auxiliary suction outlet, can be properly opened through the adjusting plate suction outlet. Since the feeding mixer is working, the raw material after mixing can be discharged from the screen in time.
  倘若调节板的开度过小,进风量不大,搅拌室内的负压小,搅拌物排出不畅,搅拌物过度粉碎,搅拌室内的热量不能及时排出,自上料搅拌机必然“发烧”。自上料搅拌机“发烧”时须检查调节板的开度。
  If the opening of the regulating plate is too small, the air intake is not large, the negative pressure in the mixing room is small, the mixing is not smooth, the mixing is excessively crushed, the heat in the mixing room cannot be discharged in time, and the feeding mixer must have a “fever”. Check the opening of the adjusting plate when the feeding mixer is “feverish”.
  搅拌物料沉降室的空间要尽量大,是路通畅的保证,有利于搅拌物料顺利及时的排出。所以在设计时应预留适当空间以满足工艺要求。
  The space of mixing material settlement chamber should be as large as possible, which is the guarantee of smooth road and conducive to smooth and timely discharge of mixing material. Therefore, appropriate space should be reserved in the design to meet the requirements of the process.
  因自上料搅拌机锤片高速旋转打击、磨擦物料,物料中的水分和微细粉尘会被脉冲除尘布袋布袋粘附,风阻增加,随着时间的增长,除尘布袋的风量和风压会有所损失,严重时会使粉碎机“发烧”,产量降低,须及时更换或者清洗除尘布袋的布袋。
  Because of the feeding high-speed mixer hammer blow, friction material, the moisture in the material and fine dust will be pulse dust bag bag adhesion, wind resistance increases, as the growth of the time, dust bag air volume and air pressure will have loss, serious when make the mill “fever”, reduced production, must be timely to replace or clean the dust bag bag.
  自上料搅拌机使用不当,长期处于超负荷状态下工作,也会引起自上料搅拌机发烧,甚至烧电机。良好的工况是电机工作在90%的额定负载下。在正确的分析了机器的磨损原因后,我们可以积极的改正,让机器在正确的使用方法跟正确的电压情况下使用。
  Improper use of self-feeding mixer, long-term work under overload state, will also cause a fever of self-feeding mixer, or even burning motor. A good operating condition is that the motor operates at 90% of its rated load. In the correct analysis of the wear of the machine, we can actively correct, let the machine in the correct use method and the correct voltage under the condition of use.
  如果大家在使用操作自上料搅拌机的过程中发现它的零件破损速度非常的快的话,一定要想办法找出具体的原因并且进行解决。更多问题的原因您可以来网站www.zishangliaojiaobanji.cn咨询。
  If you find that its parts are damaged very fast in the process of operating the self-feeding mixer, you must try to find out the specific reasons and solve them. More problem you can to website www.zishangliaojiaobanji.cn.

推荐阅读/ Recommended reading

在使用小型混凝土搅拌机之后,用户非常烦躁清理滚筒内残留的混凝土,一旦干了就难以清理,这是用户很头疼的事情,有什么办法可快速清理滚

自上料搅拌机电路系统检查测量时... 2022-06-22
搅拌机的操作过程中要注意液压油... 2022-06-20
小型混凝土搅拌车的多项检查规定 2022-06-17
从维修角度看保养搅拌车注意的问题 2022-06-15
自上料搅拌车春季保养小贴士 2022-06-13
污物进入工作油液会引起搅拌机零... 2022-06-10
小型混凝土搅拌机轮胎的异常磨损... 2022-06-08
司机在搅拌机操作中需要注意的事情 2022-06-06

截屏,微信识别二维码